Project
Profile
Wall
Fixings
Sections
Divide the wall into sections of neighbouring fins – each section has its own twist type and pattern (e.g. end to end on the left, a random 180° mix in the middle). Click a section to edit its twist below; change the last fin number to move a boundary.
Twist
Draw lines across the wall with Draw line on the drawing toolbar (or pick a line pattern there). With between each pair, lines 1 + 2 make the first band, 3 + 4 the second. Each fin twists where it crosses a band, so the twist gets longer where the band is wider. Twists are never made shorter than 4 × width per 90°. Rounding the lengths more coarsely gives fewer machine set-ups.
Each fin is given a random twist type, angle, length and height. Twists are kept at least 4.5 × width per 90° long so they stay makeable. Fewer different lengths = fewer machine set-ups = lower cost. Press New random mix for another arrangement.
| Value | Variation | – | Cycles | |
|---|---|---|---|---|
| Twist angle (°) | ||||
| Twist length (mm) | ||||
| Twist centre height (mm) |
Rounding keeps the number of different fin types down – every different fin type needs its own machine set-up.
Pattern ideas are shown as pictures under the drawing.
Drag the view angle to see how the screen changes as you walk past it. The table under the drawing lists the selected fin's twists as numbers.
Fin types & checks
Send for quotation
Save this design and send the file to Alubend for a quotation. The file contains the profile, the wall layout and every fin's twist.
Alubend USA LLC · www.alubend.com
Alubend Twisted Fin Walls – Guide, Principles and Criteria
Alubend USA LLC · November 2026
What the tools are
Alubend twists aluminium extrusions – façade fins, solar shading blades and screen profiles – along their length. Alubend's design tools use the same twisting rules as our production floor, so what an architect designs is what Alubend can make. All dimensions are in millimetres (1 in = 25.4 mm).
- Twisted Fin Wall Designer (for architects and designers). Lay out a wall of twisted fins, vary the twists across the wall, see the result from any viewing angle, and check every fin against Alubend's twisting limits. The design is saved as a file and sent to Alubend for a quotation. It contains no prices.
Both are single HTML files. They open in any modern browser (Chrome, Edge, Safari, Firefox), work offline, and need no installation or account.
How to use the wall designer
- Units – switch between metric (mm) and imperial (in) at the top right at any time.
- Profile – choose an Alubend Eclip blade (100 to 500 mm / 4 to 20 in wide) or drop in your own DXF section. Width, depth and weight are read from the drawing.
- Wall – (if a height or spacing looks like the wrong unit, e.g. 18 mm instead of 18 m, the designer offers to correct it) number of fins, spacing between fin centres, fin height, and the angle the fins start at the bottom: 0° flat (wide face to the street), 90° edge-on (narrow end to the street, like Styne House), or any angle in between – e.g. 30° or 45°, common on car-park screens. Each section can have its own bottom angle, and any single fin can be set on its own.
- Fixings – choose how the fins are held: top & bottom rail (head and base channel), hidden spigots (concealed pins into floor and soffit), wall brackets (stand-off brackets back to the building) or car park – slab edges (a bracket at every deck edge – enter the floor-to-floor heights, bottom deck first). Set the maximum span between fixings (until Alubend confirms its bracket rules, a placeholder of 12 × the profile width is used) and the bracket stand-off. Intermediate fixings are added automatically when a span is too long. Fixings show on the elevation and in 3D, and a fixing schedule lists how many of each are needed and how many bracket angles that means.
- Brackets (wall and car-park fixings) – choose from the Alubend bracket catalogue: Concept 2 – 0° saddle (curved saddle plate on the fin face), Concept 2 – 90° fork (fork plates either side of an edge-on fin), and adjustable versions of each for fins turned up to about ±30° (range to be confirmed). Auto picks the right one at every fixing from the fin's angle there; fixings where no bracket suits (e.g. a fin at 45°) are flagged. The fixing schedule counts each bracket model.
- Keep twists clear of the fixings (on by default) moves every twist into the straight part between brackets – a bracket cannot sit on a turning fin. If a twist cannot fit, it is shortened (never below the twisting limit) or flagged, with the clashing fixings ringed in red.
- Sections – split the wall into sections of neighbouring fins, each with its own twist settings – for example end-to-end twists on fins 1–20, a random 180° mix on fins 21–45 and a single 1 m twist on fins 46–60. Split selected section divides a section in two; type the last fin number to move a boundary; click a section (in the list or on the elevation) to edit its twist. Everything below applies to the selected section.
- Twist – choose whether angles are entered as the amount of twist or as the angle at the top end (e.g. start 45°, finish −45°: the designer works out the 90° twist). Then choose the type:
- Single twist – the fin turns once, with straight sections above and below.
- Twist and return – the fin turns, runs straight, then turns back.
- End to end – the fin twists over its whole height (the only option for profiles wider than 420 mm / 16.5 in).
- Follow the drawn lines – draw lines across the wall (or pick a line pattern) and the fins twist where they cross them: either between each pair of lines (a band – the twist is longer where the band is wider) or centred on each line with a set twist length. Choose the angle, whether every fin turns the same way, alternates fin by fin or reverses on every second band, and how coarsely to round the lengths (coarser = fewer set-ups).
- Random mix – every fin is different: set the share of fins that are straight, have one twist, two twists or an end-to-end twist, the twist angles (e.g. 90, 180), the range of twist lengths and how many different lengths to use. Each fin gets a random type, angle, length and height. New random mix shuffles the arrangement.
- Variation – within a section, for the single, return and end-to-end types, angle, twist length and twist height can each vary across the wall: Gradient, Peak in centre, Wave, Random or Alternate.
- Pattern ideas – a gallery of pictures directly under the drawing. Each one is a small live preview drawn with your own profile, height and finish, so you can see what a ripple, a stagger or a wave band will look like before choosing it. Click a picture to apply it to the selected section; the chosen one is outlined. Line patterns (marked lines) show their guide lines in red. Every pattern adjusts itself to stay within the twisting limits of the chosen profile. Lounge partition gives black fins edge-on with twists at mixed heights – the look of an airport-lounge or hotel-lobby screen.
- Edit on the drawing – click a fin and its twists appear on the elevation as orange boxes with their dimensions:
- drag a box up or down to move the twist;
- drag the orange handle at the top or bottom to make the twist longer or shorter;
- double-click a twist (or its label) to type the exact length, start, end and angle, reverse its direction or delete it;
- choose + One twist or + Two twists (and the angle), then click on any fin where the twist should go – it replaces whatever it overlaps;
- Snap to grid lines twists up on a grid (e.g. every 250 mm / 6 in), like notes on a stave; Align to grid snaps every hand-placed twist onto it;
- ✎ Draw line – click points across the drawing from left to right, then double-click or press Enter. Drag the white points to reshape any line; click anywhere on a line to add another point there (as many as you like); select a point and press Delete to remove it. The line patterns in the gallery (Wave band, Rising band, Two bands, Diagonal lines, Ripple lines) give ready-made starting shapes; Clear lines on the toolbar removes them all.
- Delete removes the selected twist, Esc steps back. Hand-placed twists are kept in the saved design. The table under the drawing shows the same twists as numbers.
- Background – the Backgrounds gallery under the pattern ideas shows each option as a small picture with your fins in front (Hide folds it away):
- Office – glazed facade (refurbishing an office, like Styne House), Car park – open concrete decks (decks, columns and parked cars – twisted fins are ideal for open car-park sides), Older brick wall with windows (a low-cost feature for a plain or tired elevation) – all drawn to scale and repeating floor by floor, so they work from a single storey up to 20 m and more;
- Office partition (open-plan office behind a 3–4 m fin partition) Reception feature wall (lobby with reception desk; over about 5 m it becomes double height with a mezzanine) and Lounge interior (an airport / hotel lounge photo – its ceiling line sits level with the top of the fins and it repeats sideways to fill any partition length; pairs well with the Lounge partition pattern);
- Real photos, true to scale – the car park, office glazing and brick building photos are calibrated (each floor measured in the photo) and repeat floor by floor and bay by bay to fill any wall, so a 3 m storey in the photo is always 3 m next to the fins – never stretched. Their floors follow the floor-to-floor height you set (office 3.6 m, brick 3.5 m by default); with car-park fixings they follow your deck heights, so the slabs in the photo line up with the slab-edge brackets. With Line floors up with the top and bottom of the fins ticked (the default), the floor height is adjusted slightly so a whole number of floors fits the fin height exactly – e.g. 11 m fins in front of the office give three 3.67 m floors, so the top floor line sits level with the top of the fins. If a floor has to be squeezed or stretched more than 10 % to fit, the designer says so. The office-interior and reception photos are sized to the fin height automatically. Photos from Unsplash, free to use under the Unsplash License (photographers: Humberto Arellano, CeKuhn, Rishab Lamichhane, Arlington Research, Aalo Lens, Neon Wang);
- Your own picture – drop in a photo, screenshot, JPEG, PNG or GIF (or drag it onto the gallery). Press Calibrate (2 clicks), click two floor lines in the picture (or the ground and a known height) and type the real distance between them. Tick Repeat this storey to tile that floor up the whole wall at true scale, or untick it to keep the single picture correctly scaled with the fins starting on the lower line. You can still adjust the sideways shift and how strongly it shows. The picture is saved in the design file.
The background appears in the elevation, the pattern previews and the 3D view.
- View – switch between Elevation (flat, for editing), 3D view and Both (flat on top, 3D underneath updating as you edit). Turn and tilt the 3D view with the sliders or by dragging on it; the buttons Isometric, Other side, Walking past, Straight on and From above jump to typical views. Pick a finish and show or hide the top and bottom rails. Download image saves whichever view is showing.
- Check – fins outside the limits are marked red (not possible) or amber (very hard). The fin-type table lists every different fin and how many of each.
- Send – Download design file (or Copy design code and paste it into an email) and send it to Alubend with your project details.
Twisting principles
Severity depends on width and length together
How hard a twist is depends on the profile width compared with the twist length, not on the angle per metre. A 100 mm blade twisted 90° over 1 m is the same difficulty as a 200 mm blade twisted 90° over 2 m. The outer edges of the blade stretch more as the twist gets tighter, so the governing figure is:
k = twist length ÷ (profile width × twist angle ÷ 90°)
| k | Rating | Meaning |
|---|---|---|
| 10 or more | Easy | e.g. 200 mm (8 in) wide, 90° over 2,000 mm (79 in) |
| 4.5 – 10 | Standard | routine production |
| 3.75 – 4.5 | Hard | within 50 % of the limit |
| 3 – 3.75 | Very hard | within 25 % of the limit – a paid trial is advised |
| below 3 | Beyond limit | not offered as standard (e.g. 200 mm wide, 180° over 600 mm) |
The limit is k = 3: a 200 mm (8 in) blade twisted 90° over 600 mm (24 in). The tightest twist for any blade is therefore 3 × width per 90°.
Width limits
- Up to 420 mm (16.5 in) wide: the twist can be anywhere along the fin, with straight sections either side. The profile passes through the twisting clamp, which is 420 mm (16.5 in) wide.
- 420 – 762 mm (16.5 – 30 in) wide: twist end to end only – no straight sections are possible.
- Above 762 mm (30 in): not possible.
Bottom and top ends
A fin can start at any angle at the bottom – 0° flat (wide face showing), 90° edge-on (narrow end showing) or anything in between such as 30° or 45°. That is simply how it is turned when it is fixed; every twist then turns it from there. Starting at 45° with a −90° twist finishes at −45° – the classic car-park louvre. A 90° twist turns a flat fin edge-on; 180° brings it back to flat (reversed). The angle is the same part either way – only the fixing changes – so fins with the same twist but different bottom angles are still one fin type for production. The fin-type table shows each fin's bottom → top end, and the designer warns when the top ends finish in different directions, because the top fixings or rail must suit each one.
Several twists on one fin
- Leave at least 3 × the profile width of straight between twists.
- Each extra twist on the same fin is a separate, more difficult operation.
Material
- Twisting is done in 6063 T4 temper as standard, which we can specify on the large orders typical of twisted walls.
- Other tempers (for example T6) only for gentle twists or customer-supplied material, after review.
- Finishing (anodising or powder coating) is done after twisting.
Fin types and set-ups
Every different twist (length or angle) needs its own machine set-up and test piece. A fin with two twists uses the set-ups of both twists; fins that reuse a twist share its set-up. Fins that differ only in where the twist sits (its height) share the set-up and need only a quick adjustment of the machine. For best value:
- round angles (e.g. to 15°) and lengths (e.g. to 100 mm) – the designer does this for you;
- in a random mix, keep the number of different twist lengths low (3–5) – the twist heights can still vary freely;
- use patterns that repeat a few fin types rather than making every fin different.
Production allowances
- Each bar is gripped at both ends: 2 × profile width of extra length at each end, cut off after twisting.
- At least one test piece per fin type; on larger orders up to 5 % extra pieces for testing and set-up.
Clearance between fins
Twisted fins sweep a wider footprint than the flat blade. The designer warns when neighbouring fins could touch at any height – increase the spacing or reduce the twist.
Who to contact
Alubend USA LLC · 1220 Claussen Drive, Woodstock, IL 60098 · www.alubend.com